Pin Insulation Heat Tester

Aplikasi: Pin insulation heat tester.
Untuk menguji ketahanan konektor pin isolasi plug/steker terhadap panas yang tidak normal.


Untuk menentukan pengujian ketahanan terhadap panas abnormal isolasi lengan pin konektor, di menurut IEC 60884-1 angka 40, alat uji ini terdiri dari isolasi piring A dan bagian logam B. Antara dua bagian ruang udara dari 3 mm harus disediakan dan jarak ini harus diperoleh melalui cara-cara yang tidak merugikan sirkulasi udara di sekitar pin.

Standard Outfit:
1 isolasi piring A, yang bulat dan datar, tebal 5 mm, memiliki diameter sama dengan dua kali maksimum dimensi yang diizinkan keterlibatan wajah steker diberikan dalam lembar standar yang relevan,

5 bagian logam B, kuningan, panjang minimal 20 mm, bentuk yang sama seperti garis maksimum steker menurut lembar standar yang relevan,

1 thermo kopel, tipe K, dimasukkan pada jarak 7 mm dari permukaan depan bagian logam B dalam posisi simetris 

Spesifikasi:
Model: CPL-A40.1
Sumber daya: AC220V, 50Hz
Dimensi: 450 x 350 x 350
Gap antara papan isolasi dan logam B: 3 mm
Jarak antara logam thermo pasangan & B: 7 mm
Logam lubang baut B: lebih dari 0,1 mm  
Sampel Uji: Plug, Steker, dsb.
Sesuai standar: SNI IEC 60884-1 Gambar 40

---

Sales & Online Support:

Local Phone/Fax:  021-2984-1193,  GSM Celluler: 0812-1312-5950 / 0899-0070-146 

http://www.alatuji-sni.com, info@alatuji-sni.com

Share:

Read More

Cord retention tester

Aplikasi:
Menguji kekuatan retensi kabel terhadap daya tarikan/beban mekanis & untuk memeriksa efektivitas retensi kabel dari kabel senur.
Ketegangan kabel dikendalikan dengan menggantung bobot dan dapat disesuaikan dengan penambahan 10N sesuai dengan massa atau arus dari sampel yang diuji. Mesin akan otomatis berhenti ketika jumlah dari tarikan selesai.

Spesifikasi:
Model: CPL-F20.A
Sumber daya: AC220 V, 50Hz
Dimensi (mm): 550 x 700 x 350
Jumlah test tarikan: 1~9999( Bisa diatur, Defaulnya 100 Tarikan)
Rate Pengujian: 60 times/min
Beban : 10N(1 Pcs), 60N(1 Pcs), 20N (2 pcs)
Sesuai standar: SNI IEC 60884-1 gambar 20,SNI 04-3892.1, IEC 61010, EN 61010,VDE0620

---

For testing cord retention is for check the effectiveness of the retention of the cable of the cord anchorage . The cord anchorage is used in the normal way, clamping screws, if any, being tightened with a torque equal to two-thirds of that specified in standard. After reassembly of the specimen, the component parts shall fit snugly and it shall not be possible to push the flexible cable into the specimen to any appreciable extent. The specimen is placed in the test apparatus so that the axis of the flexible cable is vertical where it enters the specimen. - The flexible cable is then subjected 100 times to a pull of - f 50 N if the rated current is 2,5 A, - 60 N if the rated current is above 2,5 A, but not more than 16 A and the rated voltage is up to and including 250 V, - 80 N if the rated current is above 2,5 A, but not more than 16 A and the rated voltage is above 250 V, - 100 N if the rated current greater than 16 A.

Power Supply : 220V  50Hz
Dimension (mm) : 540 x 240 x 860
Application: for testing cord retention is for check the effectiveness of  the retention of the cable of the  cord anchorage
Subject : Flexible Cable
Rate of Testing : 60 times/min
Counter Display : 6 Digit
Mass : 10N=1pcs,60N=1pcs,20N=2pcs (5,6,8,10 Kg)
Pull Speed/length of Pull : 1 pull for 1 second
Number of pull : 100 times to Pull
Conforms to standard : SNI IEC 60884-1 Figure 20

Share:

Read More

Switch and Rotary Test Apparatus

Aplikasi Switch and Rotary Test Apparatus:
Untuk menguji kuat mekanis dan perilaku dalam penggunaan normal, untuk menghidupkan dan mematikan saklar untuk keperluan rumah tangga dan sejenis yang memiliki arus resistif beban hingga 16A

Model	: SWA-03
Suplai daya	: AC 220V, 50Hz
Kategori	: Alat uji tusuk kontak
Dimensi(mm)	: 600x600x1500
Berat (Kg)	: Approx. 63Kg
Produk/sample uji	: Switch tekan, Switch putar
Sesuai standar	: SNI IEC

---

Electromotor is provided by 3-phase voltage 220 V that's generated by frequency electrical device (motor controller) with feed-back regulation. The controller additionally allows steplessly adjustable braking (and acceleration) that's performed every time before and when the modification of direction of the tube. this could be done to make sure uniform unwavering periodic of the tube. this is additionally restricted for the rationale of motor protection. If periodic tube strikes in obstacle throughout operation, adjustable electronic current clipper limits the torsion on the shaft of electromotor and protects the tube, the motor and therefore the obstacle (person or sample). periodic tube stops till the obstacle is removed, and at that time unremarkably continues periodic .

Share:

Read More

Conductor Damage Checker

Aplikasi:
- memeriksa tingkat kerusakan kawat konduktor kabel
- menilai apakah desain dan struktur dari terminal klem sekrup dapat merusak kawat konduktor kabel
- memeriksa apakah terminal klem sekrup tahan stres/tarikan selama proses penggunaan normal.

---

Spesifikasi:

Model Dimensi Sumber Daya Platen Diameter Circular Radial/Diameter (mm) Kecepatan Putaran Periode Lama Uji Jarak Platen dengan Terminal(H)(mm) Load Beban(Kg) Conductor Sample Test Sesuai Standar

: CDC-A11 : 600x600x950 : AC 220V, 50 HZ : 75mm : 37.5/75 : (10 ± 2) rpm : Approximately 15 minute : 260 & 280 (± 15) : 0.3, 0.4, 0.7, 0.9, 1.4, 2.0 : 75mm longer than H : SNI IEC 60884-1 Gambar 11

Share:

Read More

Tumbling barrel test machine

Aplikasi:
Alat uji yang berfungsi untuk mensimulasikan kondisi jatuh berulang suatu part kecil atau komponen seperti steker/plug, dll.

Model: CPL-TB
Sumber daya: AC220V, 50Hz
Dimensi(mm): 650X650X1000
Ketinggian jatuh untuk sample:  500 mm
Bidang permukaan jatuh: 20 mm kayu blackwood/plywood
Kecepatan berputar: 5 rotasi/menit
Jumlah jatuh:  10x jatuh/minute
Produk/sampel uji: Steker, Plug, Soket, Komponen kecil,dll.
Sesuai standar: SNI IEC 60884-1,SNI IEC 60068-2-31

Share:

Read More

Salt spray tester

Aplikasi:
- Untuk mensimulasikan efek korosif suatu peralatan jika terkena kabut garam.
- Menguji ketahanan korosi suatu produk. Biasanya pengujian dilakukan setelah permukaan material produk tesebut di plating listrik, anodizing, setelah proses pengecatan, powder coating, dll.


Model: SST-D02
Kapasitas Ruang Test : 270
Kapasitas Tangki : 15 liter
Dimensi ruang test (mm): 900 x 500 x 600mm
Temperatur : 35 ~ 50 Derajat
Sumber daya: AC220V, 50Hz
Base Material: PVC
Dimensi (mm): 1460 x 1280 x 910
Berat : Approx. 65 Kg
Sesuai standar: SNI IEC 60068-2-11, ISO 9227,SNI IEC 60068-2-52

Share:

Read More

Switch test apparatus

Aplikasi:
- Menguji daya tahan untuk switch tombol & switch push(tekan),
- Berlaku untuk peralatan rumah tangga dan sejenisnya. Juga untuk memeriksa instalasi listrik rumah dan uji lama pemakaian pada operasi normal.
- Menilai apakah switch mampu bertahan dalam penggunaan normal dari kerusakan mekanis
- Untuk memeriksa apakah sampel uji yang berlebihan pemakaiannya menjadi tidak aman dan berbahaya.


Model: CPL-S21
Sumber daya: AC220V, 50Hz
Jumlah stasiun uji: 3 sampel uji
Penggerak: Pneumatic
Penekan: Foam
Konstruksi : Stainless Steel
Dimensi: 450 x 350 x 350
Sesuai standar: IEC60884-1, IEC61058-1, IEC60669-1

Share:

Read More

Drip box IPX12

Aplikasi:Menguji perlindungan/tingkat proteksi suatu produk terhadap tetesan air sesuai dengan 2 angka karakteristik proteksi(Index Protection), yaitu IPX1 "Perlindungan terhadap tetes air" dan IPX2 "Perlindungan spesimen dalam posisi miring terhadap tetesan air.

Model: WT-IP12
Sumber daya: AC220V, 50Hz
Dimensi: 750 x 750 x 2100
Kategori: Proteksi terhadap air
Nozzle air: Stainless, Spasi 20 mm
Sampel uji: Air Conditioner, Pompa air, Lampu penerang jalan, dsb.
Posisi sampel: Dapat diatur, 200 mm s/d 180 mm
Dilengkapi dengan tangki suplai air & turntable.
Sesuai Standar: SNI IEC 60529 clause IPX1 and IPX2.

---

This machine for  checking  the  protection  against  water  to  prove  the  degrees  of  protection  with  the second characteristic numerals 1 "Protection against water drops" and 2 "Protection of a specimen in a position of tilt against water drops.

• water  tank  with  drip  nozzles  in  the  bottom spaced  20  mm
• drip nozzles of stainless steel.
• slider   holding devices  each  for  suspending,  precisely adjustable for leveling, 
• water  flow controlling valve with flow indication to  feed  or  to drain  the  water.
• with water filter to hold foreign material for drip nozzle.
• with water tank storage to supply water tank drip.
• water tank material with stainless steel 
• rip height from 200 mm to 2000 mm infinitely adjustable with a maximum height of the specimen  
• include rotation turntable  for IPX2 with adjustable speed
• automatic switch off for turntable if doesn’t needed for another test.

Share:

Read More

Water jet tester

Aplikasi:
Menguji perlindungan suatu produk terhadap masuknya air dan untuk membuktikan tingkat proteksi sesuai Index Protection 5/IPX5 yaitu "Perlindungan terhadap tembakan/jet air" atau IPX6 "Perlindungan terhadap jet  air yang kuat".
Pegangan jet dilengkapi dengan pengukur tekanan(pressure gauge). Nozel mudah diganti sesuai dengan index proteksi. Bahan nozzle dan tabung terbuat dari stainless steel.



Model: WP-IP56

Kategori: Proteksi terhadap air, Alat uji umum

Sampel uji: Pompa air, Lampu mobil, dsb.
Sesuai Standar: SNI  IEC 60529 gambar/figure 6, SNI IEC 60335-1 klausul 15.1. 1,  SNI IEC 60598 gambar/figure 8.

---

for checking the protection against ingress of water to prove the degrees of protection with the second characteristic numerals 5 "Protected against water jets" or 6 "Protected against powerful water jets" 

• nozzle element with knurling,
• handle, internal diameter approx. 16 mm, handle sleeve of plastic.
• flow meter, almost independent of position.
• flow control and stop valve with handwheel to adjust the water flow, with spout for hose of nominal width 19 mm (3/4"),
• hose, nominal width 19 mm (3/4"), 5 m long, with 2 hose clamps. nozzle element and tube within the handle of stainless steel, valve nickel-plated,

Share:

Read More

Low impact fall tester

Menguji ketahanan plug/steker terhadap tumbukan yang di berikan pada sampel uji. Hasil uji harus menunjukan tidak adanya kerusakan

Model: UT-001
Deimensi: 300 x 150 x 450
Sampel uji: plug/steker
Sesuai standar: SNI IEC 60884-1, gambar 27

---

The specimens are subjected to an impact test by means of an apparatus as shown in figure 27. The apparatus, positioned on a pad of sponge rubber 40 mm thick, is placed together with the specimens in a freezer at a temperature of (–15 ± 2) °C, for at least 16 h. At the end of this period, each specimen, in turn, is placed in the normal position of use as shown in figure 27, and a weight is allowed to fall from a height of 100 mm. The mass of the falling weight is (1 000 ± 2) g. After the test, the specimen shall show no damage within the meaning of this standard

---

Share:

Read More

On off timer

Aplikasi:
Menguji sirkuit terhadap kondisi hidup dan mati sesuai dengan interval yang telah ditentukan. kondisi hidup dan mati dapat di setting susuai dengan standar yang ditetukan.
Model : GT-S03
Sumber daya: AC220V, 50Hz
Dimensi (mm): 350 x400 x 350
Tipe produk: Alat uji/mesin uji umum
Subyek uji: Semua alat yang harus di uji terhadap kondisi hidup nati. Seperti lampu luminer, dsb.
Sesuai standar: SNI IEC 60598-1

---

Circuit for testing the thermal resistance from the die to the life cycle of the luminaire series that will lead down to the terminal voltage test.

• Input Voltage   220V, 50Hz
• Dimension  300X250X500 (millimeter)
• Weight  Approx. 15 Kg
• Digital Counter &  Timer with 4 Digit
• With buzzer for signal after the test completed
• 3 Output  terminal for connected the sample test
• Safety with emergency button to break operation

Share:

Read More

Adjustable Device Apparatus

 Alat uji ini berfungsi untuk menguji kekuatan luminer kabel fleksibel terhadap gaya puntiran dan regangan.











Spesifikasi:

Input Voltage Dimension Weight Base Construction Degree of angle rotation Sample holder Sample guide Comfort to standard

: AC 220V, 50Hz : 400 x 500 x 800 (millimeter) : Approximately 45 Kg : Stainless Steel : 360° : Clam with claw : Pulley flexible : SNI-IEC 60598-1

Share:

Read More

Ball impact tester

Untuk menguji kekuatan mekanik dan kekuatan tumbukan dengan uji jatuh bola baja, sesuai dengan SNI IEC 60598 Gambar 21, IEC 60950 klausul 4.2.5. Sebuah bola baja padat dengan diameter 50 mm dan massa 500 gr ± 25 gr, dijatuhkan bebas dengan ketinggian 1, 3 m ke sampel. Metode lainnya adalah  bola baja diikat oleh seutas tali kemudian diayunkan sebagai pendulum untuk menerapkan dampak tumbukan horisontal melalui jarak vertikal dari 1, 3 m ke sampel.

Spesifikasi:
2 bola baja :  diameter 50 ± 0, 3 mm,  Berat 500 g ± 25 g,
1 Tali pengayun/pengikat M4
1 frame uji,
Sesuai Standar: 60598 Gambar 21, IEC 60950 klausul 4.2.5.

Share:

Read More

Heat resistance tester

Aplikasi:
Untuk menguji ketahana isolasi pin terhadap panas yang tidak normal.

Model	: PS-003
Suplai daya	: AC 220V, 50Hz
Kategori	: Alat uji tusuk kontak
Dimensi(mm)	: 400 x 400 x 400
Berat (Kg)	: 20 ~ 25 Kg
Produk/sample uji	: Pin isolasi, steker, plug, dll
Sesuai standar	: SNI IEC 60884-1 gambar 40

---

Order
To determine testing resistance to abnormal heat of insulating sleeves of plug pins, in according to IEC 60884-1 figure 40, This test apparatus consists of an insulating plate A and of a metal part B: between these two parts an air space of 3 mm shall be provided and this distance shall be obtained through means which do not impair the air circulation around the pins.

Standard Outfit:

• 1 insulating plate A, which round and flat, thick 5 mm, have a diameter equal to twice the maximum permissible dimension of the engagement face of the plug given in the relevant standard sheet, 
• 5 metal part B, brass, length at least 20 mm, the same shape as the maximum outline of the plug according to the relevant standard sheet, 
• 1 thermocouple, type K, is inserted at a distance of 7 mm from the front surface of the metal part B in a symmetrical position 
• Insulation board : 5 mm thick round flat surface, diameter twice test diameter surface of the product. 
• Metal part B (Fixture): length of more than 20 mm, Material Brass, five pieces, can be replaced. 
• Gap between the boards of insulation and metal B : 3 mm, 
• The distance between the metal thermocouples & B: 7 mm 
• Metal bolt hole B : more than 0.1 mm

---

Share:

Read More

IPX34 Test Machine

Aplikasi:
Menguji dan memeriksa perlindungan terhadap semprotan air untuk membuktikan tingkat proteksi produk/sampel uji sesuai dengan indek proteksi IPX3 dan IPX4 "Perlindungan terhadap semprotan Air " dan . " Perlindungan terhadap percikan air"

Model: WP-IPX34
Tipe: Alat uji umum/Universal Testing Machine
Sumber daya: AC 220V, 50Hz

Sampel uji:  Pompa, Outdor Air condioner. Lampu jalan, dsb.
Sesuai standard: SNI IEC 60529 gambar/figure 4, SNI IEC 60598 klausul/clause 9.2.5, SNI IEC 60947

---

Checking the protection against water, to prove the degree of protection IPX3 and IPX4. for \”Protection against Spraying Water\” and \”Protection against Splashing Water\” tests. Oscillating tubes with spray nozzles of 0,4 mm Easy &adjustable Ring Stand for set up leveling the height Water flow rate for set the rate water supply into oscillating tube. With water filter to hold foreign material for drip nozzle. Turntable with adjustable speed Multiple of angle for rotation around sample up to 180 Speed for rotate around sample approximately 60 per second.

---

Share:

Read More

Burning Test Machine

Aplikasi: Menentukan tingkat proteksi sampel terhadap pembakaran linear/nyala api, bara api & percikan api yang dapat merusak spesimen.

Model	: FM-02
Suplai daya	: AC 220V, 50Hz
Kategori	: Flammability Tester
Dimensi(mm)	: 1100 X 600 X 800 mm
Berat (Kg)	: 75 ~ 90 Kg
Produk/sample uji	: Plastik & material lain non logam
Sesuai standar	: SNI ISO 845, ISO 9773

---

It screening procedure for comparing the relative burning behavior specimens made from plastic and other non-metallic materials, exposed to a flame ignition source of 50W or 500W nominal power. These test methods determine the linear burning rate and the after flame/afterglow times, as well as the damaged length of specimens. They are applicable to solid and cellular materials that have an apparent density of not less than 250kg/m3, determined in accordance with ISO845. Then do not apply to materials that shrink away from the applied flame without ignition; ISO9773 should be used for thin flexible materials.

• Timing device with four digit 9999X0.1s
• Automatic Carried unit device for movement of needle
• Smoke/fume exhaust Ø 113 mm incorporated in chamber
• Black painted cabinet more than 0,5 m (2.05 m )
• Gas flow regulating valve for flame height, manual adjustment
• Gas pressure regulator and safety control
• Needle burner tilt to 45° from the vertical, manual adjustment
• Ring Stand easy to grip the sample
• Preset time of testing; 5s, 10s, 20s, 30s, 60s, 120
• Lighting inside the cabinet and fan control
• Easy manual panel control with push button lamp
• Timer Display for record data time burning, time flame
• Time for temperature to increase (100° to 700°; 23,5 s)
• Combustion angle 0 , 20 , 45
• Height of flame Up to 125 mm
• Gas Supply Propane min 95% purity

---

Share:

Read More

Mechanical shock tester

$00.00

Mechanical Shock Tester dirancang untuk menguji MCB, ELCBs . Tujuannya menguji ketahanan sample uji terhadap guncangan mekanik sesuai standar IEC 60898.

Sampel dipasan pada bidang plat vertikal. Ketinggian pemasangan sampel dapat disesuaikan hingga 250mm (180mm jarak normal). Jarak horizontal pelat vertikal dapt disesuaikan dan diputar antara 150m sampai 250mm / (biasanya 200). Menggunakan pegas dengan kekuatan 25N / mm konstan. Penggerak motor untuk mekasnisme menjatuhkan dengn tinggi 40mm.dengan kecepatan yang dapat disesuaikan. Jumlah drop/jatuh dicatat/diatur  dengan  Digital Counter.

Model:RC-MA2
Sumber daya: AC220V, 50Hz
Dimensi: 600 x 350 x 350
Sample Uji:  RCCB, MCB
Sesuai standar- SNI IEC 61008-1 gambar 11,IEC 60898. 

Share:

Read More

Open Close Test machine

MAAF HALAMAN INI SEDANG DALAM MAINTENANCE.
Silahkan hubungi Customer Support kami.

Aplikasi:

Model	:
Suplai daya	: AC 220V, 50Hz
Kategori	:
Dimensi(mm)	:
Berat (Kg)	:
Produk/sample uji	: Kulkas
Sesuai standar	:

Order

Share:

Read More